E-beam welding is a process where a high energy beam of electrons from an electron gun is accelerated and focused using electric and magnetic fields, and shot at two materials to join them. The kinetic energy of the electrons creates very high heat which melts the two materials together (electrons are particles with a very small mass, 9*10-31 kg or 2*10-30 lbs to be exact). The electron beam requires that the system be under vacuum to maintain the speed and focus of the electrons thus preventing beam dissipation or scattering (without vacuum, the electrons would run into other molecules in the atmosphere like nitrogen, oxygen, and water vapor, among others). This is where Televac® vacuum gauging comes in, to make sure that the system is under sufficient vacuum to operate correctly.
E-빔 용접, AMS 2680 및 AMS 2681에 관해서 두 가지 관련 AMS 사양이 있습니다. 두 개의 다른 진공 레벨을 1*10-4 토르와 1*10-3 Torr로 각각 호출합니다. 항공 우주 사양을 위한 것입니다. 시스템의 진공 수준 과 정확도 요구 사항에 따라 다음과 같은 중요한 차이점이 있는 Televac 진공 측정을 위한 몇 가지 옵션이 있습니다.
The first option is an active gauge solution. With an active gauge, the control electronics are attached directly to the physical sensor, then there are optional outputs to show the vacuum level including an analog 0 to 10 V output, RS-485 communications, EthernetIP, or PROFINET communications. The active gauges that would be used for E-Beam welding are an MX2A or MX4A (thermocouple vacuum gauges) for measurement from 1000 Torr down to 1*10-3 Torr and then an MX7B (cold cathode vacuum gauge) for measurement from 1*10-3 Torr and deeper vacuum (as low as 1*10-8 Torr).
두 번째 옵션은 제어 전자장치를 물리적 센서와 분리하는 것입니다. E-Beam 용접기의 다른 곳에서 원격 디스플레이가 필요하거나 원하는 경우에 이상적입니다. 이에 대한 이상적인 솔루션은 MV2A 및 2A 센서로 측정만 필요한 경우 1*10-3 Torr, 또는 2A/4A(다시1*10-3 Torr까지 거친 진공 측정을 위해) 중간 및 고진공 측정을 위한 7B와 결합된 MX200(1*10-7 Torr)입니다. 선택한컨트롤러(MV2A 또는 MX200)에따라 아날로그 0 ~5V 신호, 아날로그 0 ~ 10 V 신호, RS-232 통신, RS-485 통신 또는 이더넷IP 통신의 선택적 출력을 제공합니다.
유닛에 대해 혼란 스럽습니까? 그러지 마세요! 다음은 Torr에서 다른 일반적인 측정 단위로의 몇 가지 간단한 변환입니다 (더 많은 변환 을 원하시면 단위 변환기를 확인하십시오).
1 토르 = 1.33 mbar
토르 1mm Hg
1 토르 = 1.33 * 10-1 kPa
어떤 제품을 선택해야 할지 잘 모르십니까? 이 화면의 오른쪽 하단에있는 창을 사용하여 우리와 채팅하거나 +1 215 947 2500으로 전화하거나 [email protected] 로 이메일을 보내주십시오!
E-빔 용접은 대기 중에도 수행할 수 있습니다. 빔이 대기 중의 다른 분자/가스를 타격하는 데 서식하기 때문에 용접은 일반적으로 더 넓으며 특정 응용 분야에는 적합하지 않을 수 있습니다.
Active Vacuum Gauge Solutions
MX2A Thermocouple (Pirani)
1*10-4 Torr to 1000 Torr
MX4A Convection (Pirani)
1*10-4 Torr to 1000 Torr
MX7B Cold Cathode
1*10-8 Torr to 1*10-3 Torr
MX Active Gauge EthernetIP Gateway
5*10-11 Torr to 10,000 Torr
Vacuum Controller Solutions
MX200
1*10-11 Torr to 10,000 Torr
MX200 EthernetIP
1*10-11 Torr to 10,000 Torr
MX200 PROFINET
1*10-11 Torr to 10,000 Torr
MV2A
1*10-3 Torr to 20 Torr
2A Thermocouple (Pirani)
1*10-3 Torr to 20 Torr
4A Convection (Pirani)
1*10-4 Torr to 1000 Torr
7B Penning Magnetron Cold Cathode
1*10-7 Torr to 1*10-3 Torr