- Vacuum controller for up to (4) Televac® MX active vacuum gauges and (1) CDG
- EthernetIP connections to the Televac® MX2A, MX4A, MX7B, and MX7M Active Vacuum Gauges
- Cavi standard Cat5e a basso costo per collegamenti di vacuometri
- Riduce notevolmente la latenza dei segnali analogici (HMI/visualizzazione del mismatch del display del misuratore di vuoto)
- Calibrare digitalmente i vuotometri dal vostro HMI
- Configure all settings for Televac® MX series active vacuum gauges
- Alimentazione 24 V DC al gateway di alimentazione e ai vacuometri collegati
- Connessioni di alimentazione opzionale ±15 V DC per CDG
- Montaggio a rack e a pannello
- EthernetIP per il semplice collegamento del vostro controllore di pressione del vuoto ad un PC, PLC e altre apparecchiature
- Connessioni di Classe 1 (ciclica) e Classe 3 (aciclica) supportate
- Indirizzo IP programmabile e abilitazione/disabilitazione DHCP
- Funzionamento con porta 10/100 Mbit, mezza porta o full duplex
- Firmware aggiornabile sul campo via USB
- LED di stato per l'attività di rete/modulo di stato/dati della porta
- Accesso web sicuro per i dati e le impostazioni della rete e del gateway tramite un browser web
- Eccellente assistenza clienti
The MX Active Gauge EthernetIP Gateway (sometimes also called an EthernetIP vacuum controller, EthernetIP vacuum control unit, or EthernetIP vacuum pressure controller) is the first and only solution designed to provide an EthernetIP connection between Televac® active vacuum gauges and Rockwell Automation® Allen-Bradley® PLCs. An increasingly popular industrial network communication standard, EthernetIP communication offers users faster and more reliable vacuum measurements and eliminates the need for additional analog-to-digital converters or other vacuum controllers and vacuum pressure controllers.
Gateway di controllore di vuoto EthernetIP compatibile con i vacuometri attivi compatibili con EthernetIP
This EthernetIP vacuum control unit supports an easily configurable network of up to (4) Televac® active vacuum gauges and (1) capacitance diaphragm vacuum gauge (CDG) through EthernetIP communications. Multiple gateways can also be daisy-chained together for additional vacuum gauge connections (made possible by dual EthernetIP ports on the back of the unit). The gateway allows users to interface directly with supported PLCs and PCs, including the ability to read vacuum measurements and change vacuum gauge settings from a convenient, remote location without complicated conversion tools. In addition to Televac vacuum gauges, the gateway supports CDGs from MKS, Inficon, Leybold, Brooks, and Setra. 24 V DC and ±15 V DC with D-sub 15 (DB15) and D-sub 9 (DB9) connectors are supported.
MX Active Gauge Gateway EthernetIP
Adattatori RJ45
Cat5e Ethernet Cables
| Campo di funzionamento | 5*10-11 Torr to 1*104 Torr |
| Communications (External) | EthernetIP |
| Communications (Active Gauges) | RS-485 |
| Manometro attivo RS-485 Indirizzi | 1 to 4 |
| Misuratore attivo RS-485 Baud | 38400 |
| Tensione di alimentazione | 22 V DC to 26 V DC |
| Potenza massima | 30 W max |
| Temperatura di esercizio | 0 °C a 50 °C |
| Temperatura di stoccaggio | da -20 °C a 70 °C |
| Maximum Active Gauges Controlled | 4 |
| Massimo CDG controllato | 1 |
| Tempo di risposta | ≤100 ms |
| P1 | EthernetIP RJ45 port 1 to PLC/PC |
| P2 | EthernetIP RJ45 port 2 to PLC/PC |
| NS | Network status LED |
| MS | Module status LED |
| 1 | Active gauge 1 connection |
| 2 | Active gauge 2 connection |
| 3 | Active gauge 3 connection |
| 4 | Active gauge 4 connection |
| CDG | CDG connection |
| 24 | +24 V DC supply |
| GND | Ground Supply |
| +15 | +15 V DC supply for CDG (optional) |
| -15 | -15 V DC supply for CDG (optional) |
| BTLD | Bookload button |
| USB | USB communication for bootloading |
| Connectors | (2) RJ45 |
| Ports | 10/100 Mbit, half or full duplex |
| DHCP | Enable or disable |
| Class 1 Connections | |
| Connection Type | Point-to-point, multicast |
| Target to Originator Instance ID | 100 |
| Data Size | 20 |
| Originator to Target Instance ID | 150 |
| Data Size | 4 |
| Configuration Instance | 3 |
| Supported Connections | 4 |
| Requested Packet Interval | 1 ms to 3200 ms |
| Trigger Types | Cyclic, change of state |
| Priorities | Low, high, schedule, urgent |
| Class 3 Connections | |
| Service | 0xE (get), 0X10 (set) |
| Class | 0xA2 |
| Instance | See ADI table |
| Data Value Attribute | 5 |
| Supported Connections | 6 |
| Requested Packet Interval | 100 ms to 10000 ms |
| Connection Type | Point-to-point |
| Trigger Type | Applicazione |
| Priority | Basso |
Please refer to the instruction manual for a complete list of Class 1 and Class 3 connection details, a complete list of ADIs, and information about the Electronic Data Sheet (EDS) file.
The RJ45 connectors labeled P1 and P2 are the EthernetIP connections that will run to the PLC or PC. The RJ45 connectors labeled 1 through 4 are the active gauge inputs. These will run through Cat5e Ethernet cables and through an adapter to attach to the active gauges in the network. All active gauges must be set to separate RS-485 addresses 1 through 4 and baud rate 38400 to communicate with the gateway. The RJ45 connector labeled CDG will connect to the CDG in the network if one is available. The CDG must be turned on through the appropriate parameter in the ADI table.
The power input connector accepts a +24 V DC and GND connection, as well as an optional ±15 V DC input to run to the attached CDG if required. Regardless of the alternate supply, the gateway and attached active gauges require the +24 V DC input to be connected in order to operate. The pushbutton labeled BTLD is to be pressed while powering the gateway to send the unit into bootload mode for the ability to easily update the firmware, and the update occurs over the USB connection.
| Involucro | Alluminio |
| Collegamenti elettrici | Connettore a 4 poli |
| Peso | 0,65 kg (1,4 libbre) |
| Certified to UL 61010-1 |
| Certified to CAN/CSA C22.2 No. 61010-1-12 |
| CE certified to EN 61010-1, EN 61236-1, EN 55011 |
| RoHS compliant |
| IP40 |
| EAC certified |
| Calibrazione tracciabile NIST opzionale |
Documentazione del prodotto
Note applicative
Strumenti
| Convertitore di misura del vuoto Televac |
Articoli
| Vacuum Measurement Using Modern Cold Cathode Technology |
Brochures
| Televac®️ Vacuum Measurement Product Catalog |
MX Active Gauge EthernetIP
Gateway Quantity Discounts
| Quantità | Discount |
| 1 | List |
| 5 | 2% |
| 10 | 5% |
| 15 | 7% |
| 20 | 10% |
| 25 | 13% |
| 30+ | 15% |
Cat5e Ethernet Cable Quantity
Discounts
| Quantità | Discount |
| 1 | List |
| 50 | 5% |
| 75 | 10% |
| 100+ | 15% |
Using the Gateway for Heat Treat and Vacuum Furnace Applications
This vacuum controller gateway is particularly useful for heat treat and vacuum furnace applications where a single gateway can eliminate the need for up to (5) analog-to-digital converter (ADC) input channels while simultaneously reducing any latency from analog-to-digital conversions (causing a mismatch between the vacuum gauge display and the furnace human-machine-interface or HMI). The EthernetIP vacuum controller gateway also gives the end user the ability to calibrate their vacuum gauges from their HMI by interfacing digitally with the vacuum controller gateway. This means no more climbing on top of your furnace to do vacuum measurement comparisons! The ability to change settings and calibrate digitally is due to the unique design of the vacuum controller gateway, where all communication with Televac® vacuum gauges is done digitally (via RS-485).
Ulteriori informazioni e prodotti simili
In sostanza si può pensare al gateway del controllore di pressione a vuoto EthernetIP come ad un convertitore da RS-485 a EthernetIP di fantasia. L'eccezione è rappresentata dall'ingresso CDG, che prende l'uscita analogica 0-10 V DC del CDG e la converte in un valore digitale (usando un convertitore analogico-digitale) che può poi essere letto attraverso EthernetIP. Se cercate una soluzione di controllore di vuoto/unità di controllo del vuoto EthernetIP (al posto dei vacuometri attivi e del gateway) date un'occhiata al nostro MX200 EthernetIP!